• 0
Shop Products $

Vu-Tight DI Liner (1/4-inch OD). Visually observe the press-tight connection between the column end and liner. Fits 0.32 and 0.53mm ID capillary columns (fits column ODs from 0.5mm to 0.8mm). Slotted top prevents obstruction of carrier gas flow. Two designs are available.

Open-End Wrenches, Restek - 20388, Open-End Wrenches, 1/4 – 3/16 IN.

1/32Replacement Nut.

Replacement Inlet Seal 1.2mm hole. Fittings use standard size two-hole capillary ferrules. Capillary columns install easily. Column insertion depth is identical to original equipment.

Stainless Steel Inlet Seals. For Agilent 5890/6890 split/splitless injection ports. 1.2mm, special grade stainless steel leak-tight seal. Use for normal analysis. Column lifetime increased because oxygen cannot permeate into carrier gas. Signal noise reduced with high sensitivity detectors. 10/pk.

Replacement Inlet Seal 1/6 hole. Fittings use standard size two-hole capillary ferrules. Capillary columns install easily. Column insertion depth is identical to original equipment.

MXT Low-Dead-Volume Y Connector, for 0.28mm ID MXT columns. Connect two MXT columns to one inlet. Connect one MXT column to two detectors.

MXT Low-Dead-Volume Connector, for 0.28mm ID MXT columns. Connect guard columns/transfer lines to MXT columns. Low thermal mass tracks rapid oven temperature programming.

1/32Stainless Steel Replacement Ferrules for MXT Connectors. 0.59mm ID. Fits Column: 0.28mm ID.

1/32Stainless Steel Replacement Ferrules for MXT Connectors. 0.79mm ID. Fits Column: 0.53mm ID.

Universal Press-Tight® Connectors, Restek - 20400, Universal Press-Tight Connectors

Universal Press-Tight Connectors. Connects gaurd columns to analytical columns. Repair broken columns. Connect column outlets to transfer lines.

Universal Angled Y Press-Tight Connectors. Alleviates column-end connection strain. Inlet and outlet ends conform to the column radius. Perform confirmational analysis with a single injection.

Universal Angled Y Press-Tight Connectors. Alleviates column-end connection strain. Inlet and outlet ends conform to the column radius. Perform confirmational analysis with a single injection.

Universal Y Press-Tight Connectors. Split sample flow onto two different columns. Split a single column flow into two different detectors. Perform confirmational analysis with a single injection. Fits 0.18, 0.25, 0.32, & 0.53mm ID columns.

Universal Y Press-Tight Connectors. Split sample flow onto two different columns. Split a single column flow into two different detectors. Perform confirmational analysis with a single injection. Fits 0.18, 0.25, 0.32, & 0.53mm ID columns.

Vacuum Vu-Union Ferrules. 0.4mm ID. Fits Column ID: 0.25 ID-0.4 OD. For use with Vacuum Vu-Union connectors. 60% VESPEL /40% graphite. 400[degree]C maximum operating temperature.

Vacuum Vu-Union Ferrules. 0.5mm ID. Fits Column ID: 0.32 ID-0.5 OD. For use with Vacuum Vu-Union connectors. 60% VESPEL /40% graphite. 400[degree]C maximum operating temperature.

Vacuum Vu-Union Ferrules. 0.8mm ID. Fits Column ID: 0.53 ID-0.8 OD. For use with Vacuum Vu-Union connectors. 60% VESPEL /40% graphite. 400[degree]C maximum operating temperature.

Deactivated, Universal Press-Tight Connectors. High-temperature silanization for excellent inertness. Ideal for trace analysis of active compounds. Ideal for the analysis of pesticides, semivolatile pollutants and clinical/forensic samples.

Polyimide Resin, Restek - 20445, Polyimide Resin

Universal Angled 'Y' Press-Tight® Connectors, Restek - 20469, Universal Angled “Y” Press-Tight Connector

Cross-Disk Inlet Seals for Agilent GCs, Restek - 20476, Cross-Disk Inlet Seal

High Capacity Oxygen Trap. 1/4 fittings. 11 x 1 1/2. Most effective oxygen trap available. Long life-typically lasts longer than five 200ft.3 cylinders. Removes up to 600mg of oxygen and 2g moisture. Reduces oxygen to 15ppb concentration.

High Capacity Oxygen Trap. 1/8 fittings. 11 x 1 1/2. Most effective oxygen trap available. Long life-typically lasts longer than five 200ft.3 cylinders. Removes up to 600mg of oxygen and 2g moisture. Reduces oxygen to 15ppb concentration.

MINICYL Regulator, 1/8 fittings.

MINICYL Regulator, 1/4 fittings.

Capillary Column Rinsing Reservoir, Complete kit.

Capillary Column Rinsing Reservoir, Reservoir only.

Refillable Hydrocarbon Trap. Carbon refill (two recharges). 11 x 1 1/2. Removes trace carrier gas impurities. 20umfrit prevents particulate contamination. Stops carrier gas interferences with purge & trap systems. Refillable and rechargeable.

Septum Nut. (similar to HP part # 18740-60835.). For 23-Gauge Needle s.

MSD Source Nut, Restek - 20643, (Detector) MSD Source Nut

1/8-inch Capillary Inlet adapter Fitting Kit. (Split/splitless fitting for 0.53mm ID capillary columns).

Dual-Stage Ultra-High Purity Stainless Steel Gas Regulators with CGA Fittings, Restek - 20662, Ultra-High-Purity Regulator

Capillary Adaptable FID Replacement Jet For HP 5890/6890 GCs (0.011-inch ID tip). (Similar to HP part #19244-80560.). Standard.

Capillary Adaptable FID Replacement Jet For HP 5890/6890 GCs (0.011-inch ID tip). (Similar to HP part #19244-80560.). Standard.

Capillary Adaptable FID Replacement Jet for Agilent 5890/6850/6890 GCs, Restek - 20672, High-Performance Siltek Treated, 0.011-Inch ID Tip

Capillary Adaptable FID Replacement Jet For HP 5890/6890 GCs (0.011-inch ID tip). (Similar to HP part #19244-80560.). High-performance.

Photoionization, PID Lamps, Restek - 20675, PID Lamp

High-Capacity Split Vent Trap. Reduces the release of hazardous materials in to the lab. Lasts one month or 1,5000 injections. Includes connecting lines and mounting kit.

High-Capacity Split Vent Trap. Reduces the release of hazardous materials in to the lab. Lasts one month or 1,5000 injections. Includes connecting lines and mounting kit.

Cyclo Inlet Liner for Agilent GCs Equipped with Split/Splitless Inlets, Restek - 20707-214, Cyclo Inlet Liner

Cyclosplitter Sleeves. For Agilent GCs. 4.0mmID, 6.3mmOD, 78.5mm long. Deactivated borosilicate glass. Cylindrical glass screw design provides a large area for sample vaporization. Use for dirty samples. Multiple injections can be shot before cleaning is required. Not for large volume injections.

Cup Splitter Sleeves. For Agilent GCs. 4.0mmID, 6.3mmOD, 78.5mm long. Deactivated borosilicate glass. The Jenning's cup design is excellent for mixing of the sample. Tortuous flow path aids in sample vaporization and minimizes molecular weight discrimination. Can be packed with wool.

Splitless Sleeves. For Agilent GCs. 2.0mmID, 6.3mmOD, 78.5mm long. Deactivated borosilicate glass. For trace samples and samples containing a narrow molecular weight distribution not prone to thermal decomposition. Wool packing is recommended. Aids in vaporization and minimizes discrimination.

Splitless Inlet Sleeves. For Varian GCs. 2mmID, 6.3mmODx74mm long. Deactivated Borosilicate glass. For trace samples and samples containing a narrow molecular weight distribution not prone to thermal decomposition. Packing with wool is recommended for rapid vaporization of the sample.

Drilled Uniliner® Inlet Liner with Hole near Bottom for Agilent GCs Equipped with Split/Splitless Inlets, Restek - 20771, Drilled Uniliner (hole near bottom)

Splitless Sleeves. For Agilent GCs. 4.0mmID, 6.3mmOD, 78.5mm long. Deactivated borosilicate glass. For trace samples and samples containing a narrow molecular weight distribution not prone to thermal decomposition. Packing with wool aids in vaporization and minimizes discrimination.

SPI Inlet Sleeves. For Varian GCs. 5mmID, 4.6mmODx54mm long. Deactivated Borosilicate glass. For 0.25 and 0.32mmID columns. Use when high linearity is desired.

SPI Liners for Varian GCs, 0.8mm SPI. 0.80 mm ID. 4.6 mm OD. 54 mm Length. Similar to Varian Part Number: 01-900109-07.

Split Sleeve with Fused Silica Wool. 4.0mmID, 6.3mmOD, 78.5mm long. Deactivated borosilicate glass. Designed for the Agilent 7673 autosampler. Packed with fused silica wool to provide a high surface area for rapid vaporization of the sample delivering a uniform vapor cloud to the split point.

Double Taper Inlet Liner for Agilent GCs equipped with split/splitless inlets, Restek - 20785-214, Double Taper Splitless, Straight

Double Gooseneck Splitless Sleeves. For Agilent GCs. 4.0mmID, 6.3mmOD, 78.5mm long. Deactivated borosilicate glass. For better containment of the sample vaporization cloud. Reduces sample backflash. Minimal adsorption and discrimination. Pack with wool for dirty samples. For trace active samples.

Cyclo Vu-Tight DI Liner (1/4-inch OD). Visually observe the press-tight connection between the column end and liner. Fits 0.32 and 0.53mm ID capillary columns (fits column ODs from 0.5mm to 0.8mm). Slotted top prevents obstruction of carrier gas flow. Two designs are available.

Deactivated Glass Wool. Wool is used to promote uniform vaporization in split or splitless sleeves. Recommended for autosamplers with fast injection rates. Wool also traps non-volatile or inorganic residue present in the sample reducing column contamination. 10g size will fill over 600 sleeves.

Splitter Inlet Sleeves. For Varian GCs. 4mmID, 6.3mmODx72mm long. Deactivated Borosilicate glass. Packed with fused silica wool to provide a high surface area for rapid vaporization of the sample, delivering a uniform vapor cloud to the split point.

Gooseneck Splitless Sleeves. For Agilent GCs. 2.0mmID, 6.3mmOD, 78.5mm long. Deactivated borosilicate glass. For better containment of the sample vaporization cloud. Reduces sample backflash onto the septa or injector surfaces. Minimal adsorption and discrimination. Pack with wool for dirty samples.

Single Taper Inlet Liner for Agilent GCs equipped with split/splitless inlets, Restek - 20799-214, Single Taper Splitless, Straight

Gooseneck Splitless Sleeves. For Agilent GCs. 4.0mmID, 6.3mmOD, 78.5mm long. Deactivated borosilicate glass. For better containment of the sample vaporization cloud. Reduces sample backflash onto the septa or injector surfaces. Minimal adsorption and discrimination. Pack with wool for dirty samples.

Laminar Cup Splitter. 4.0mm ID. 6.3mm OD. 78.5mm Length. Nominal ID at syringe needle expulsion point.

Split Liners for Perkin-Elmer GCs, Auto SYS Laminar Cup Splitter. 4.0 mm ID. 6.2 mm OD. 92.1mm Length. Nominal ID at syringe needle expulsion point.

Splitless Liners for Perkin-Elmer GCs, Auto SYS Splitless w/Wool (2mm ID). 2.0 mm ID. 6.2 mm OD. 92.1mm Length. Similar to PE Part Number: N6101372. Nominal ID at syringe needle expulsion point.

Split Liners for Perkin-Elmer GCs, Auto SYS Splitter with Wool. 3.5 mm ID. 6.2 mm OD. 92.1mm Length. Similar to PE Part Number: N6101052. Nominal ID at syringe needle expulsion point.

Split Liners for Perkin-Elmer GCs, Auto SYS Cup Splitter. 4.0 mm ID. 6.2 mm OD. 92.1mm Length. Nominal ID at syringe needle expulsion point.

GC Open-Top Uniliner Inlet Sleeves. For PerkinElmer GCs, Auto SYS. 4mmID. Deactivated Borosilicate glass. Manufactured with specifications that meet or exceed the original equipment's design. For trace, dirty, active samples.

GC Cyclo-Uniliner Inlet Sleeves. For PerkinElmer GCs, Auto SYS. 4mm ID. Deactivated Borosilicate glass. Manufactured with specifications that meet or exceed the original equipment's design. For use on trace, dirty active samples with high molecular weight.

Open-Top Uniliner Direct Injection Sleeves. For use with Agilent GCs, split/splitless injection ports. 4.0mmID. Use for trace, dirty, active samples.

SPI Liners for Varian GCs, SPI Liner with Buffer. 2.4 mm ID. 4.6 mm OD. 54 mm Length. Similar to Varian Part Number: 01-900109-08.

GC Split Inlet Sleeves. For Shimadzu GCs. 3.5mmID. Deactivated Borosilicate glass.

99mm Splitless (3mm ID) Liner. 3.0 mm ID. 5.0 mm OD. 99 mm Length. Similar to Shimadzu Part Number: 221-32544-00. Nominal ID at syringe needle expulsion point.

Brass Capillary Nut. (Similar to Varian part #03-949551-00.).

Stainless Steel Capillary Nut. (Similar to Varian part #03-949551-00.).

Inlet Stainless Steel Capillary Nut. For the HP5890 GC. Use with standard ferrules.

Splitless Sleeves. For Agilent GCs. 4.0mmID, 6.3mmOD, 78.5mm long. Deactivated borosilicate glass. For trace active dirty samples.

Splitless Liners for Perkin-Elmer GCs, Auto SYS Cyclo Double Gooseneck. 3.5 mm ID. 6.2 mm OD. 92.1mm Length. Nominal ID at syringe needle expulsion point.

Cyclo Double Gooseneck Splitless Sleeves. For Agilent GCs. 2.0mmID, 6.3mmOD, 78.5mm long. Deactivated borosilicate glass. For trace active dirty samples.

Split Liners for Perkin-Elmer GCs, Auto SYS Cyclosplitter. 4.0 mm ID. 6.2 mm OD. 92.1mm Length. Nominal ID at syringe needle expulsion point.

Splitless Sleeves. For Agilent GCs. 4.0mmID, 6.3mmOD, 78.5mm long. Quartz glass. For trace samples and samples containing a narrow molecular weight distribution not prone to thermal decomposition. Packing with wool is recommended. Aids in vaporization and minimizes discrimination.

Splitless Sleeves. For Agilent GCs. 2.0mmID, 6.3mmOD, 78.5mm long. Quartz glass. For trace samples and samples containing a narrow molecular weight distribution not prone to thermal decomposition. Wool packing is recommended. Aids in vaporization and minimizes discrimination.

Split Liners for 8000 & TRACE Series GC's, 1mm Split. 1.0 mm ID. 8.0 mm OD. 105mm Length. Similar to CE Part Number: 45320075. Nominal ID at syringe needle expulsion point.

Split Liners for 8000 & TRACE Series GC's, 3mm Split. 3.0 mm ID. 8.0 mm OD. 105mm Length. Similar to CE Part Number: 453 20031. Nominal ID at syringe needle expulsion point.

Split Liners for 8000 & TRACE Series GC's, 5mm Split. 5.0 mm ID. 8.0 mm OD. 105mm Length. Similar to CE Part Number: 453 20030. Nominal ID at syringe needle expulsion point.

Fisons GC Splitless Inlet Sleeves. For Fisons GCs. 3.0mmID. Deactivated Borosilicate glass. Meets or exceeds original equipment specifications. Use for trace samples and for samples containing a narrow molecular weight distribution not prone to thermal decomposition.

Splitless Liners for 8000 & TRACE Series GCs, Splitless (5mm ID). 5.0 mm ID. 8.0 mm OD. 105mm Length. Similar to CE Part Number: 453 20033. Nominal ID at syringe needle expulsion point.

Laminar Cup Inlet Liner for Thermo TRACE, 8000 Series and Focus GCs equipped with SSL inlets, Restek - 20949, Laminar Cup Splitter

Split Liners for 8000 & TRACE Series GC's, Cup Splitter. 4.0 mm ID. 8.0 mm OD. 105mm Length. Nominal ID at syringe needle expulsion point.

Straight Inlet Liner with Wool for Shimadzu 17A, 2010, and 2014 GCs Equipped with Split/Splitless Inlets, Restek - 20956-213, Split/Splitless, Straight

DI Uniliner® Liners for Agilent 5890 Packed Column GC, Restek - 20965, DI Uniliner Liner

1mm Split. 1.0mm ID. 6.3mm OD. 78.5mm Length. Nominal ID at syringe needle expulsion point.

17A 1mm Split Liner. 1.0 mm ID. 5.0 mm OD. 94 mm Length. Nominal ID at syringe needle expulsion point.

Recessed Gooseneck (2mm) Liner. 2.0mm ID. 6.5mm OD. 78.5mm Length. Use with two-hole ferrule for dual column analysis. Nominal ID at syringe needle expulsion point.

Recessed Gooseneck (4mm) Liner. 4.0mm ID. 6.5mm OD. 78.5mm Length. Use with two-hole ferrule for dual column analysis. Nominal ID at syringe needle expulsion point.

Recessed Double Gooseneck (4mm) Liner. 4.0mm ID. 6.5mm OD. 78.5mm Length. Use with two-hole ferrule for dual column analysis. Nominal ID at syringe needle expulsion point.

Replacement Parts for FID Collector Assembly Kit for Agilent GCs, Restek - 21001, FID Ignitor

Compact Ferrules for Agilent GCs, Fit 0.25/0.32 mm int.Ø MXT® Columns, Restek. Compact Ferrules for Agilent GCs, Fit 0.25/0.32mm ID MXT® Columns, Restek - 21007, Compact Ferrules

Compact Ferrules for Agilent GCs, Fit 0.25/0.32 mm int.Ø MXT® Columns, Restek. Compact Ferrules for Agilent GCs, Fit 0.25/0.32mm ID MXT® Columns, Restek - 21008, Compact Ferrules

Cross-Disk Inlet Seals for Agilent GCs, Restek - 21012, Cross-Disk Inlet Seal

Precision® Inlet Liner with Wool for Agilent GCs Equipped with Split/Splitless Inlets, Restek - 21023-213, Split Precision Liner with Deactivated Wool

Precision® Low Pressure Drop Inlet Liner with Wool for Agilent GCs equipped with Split/Splitless Inlets, Restek - 21033, Low Pressure Drop Precision Liner w/Deactivated Wool

Capillary Installation Gauge for Agilent GCs, Restek - 21034, Capillary Installation Gauge

Category