• 0
Shop Products $

SOLVENT TRANSFER MANIFOLD, AIRFREE. Joint size: 24/40. Used to purify and transfer solvents under inert conditions. Permits transfer of solvents directly into an evacuated storage vessel. With 24/40 standard taper inner joints and a 4mm Chem-Cap valve for vacuum control.

ADAPTER, CONNECTING, REDUCING. Top Outer Joint: 19/38; Lower Inner Joint: 24/40. Used to connect dissimilar standard taper joint sizes. Lower inner joint is larger in size than the top outer joint.

ADAPTER, INLET, INNER, JOINT, 90[degree]. HxW: 70x50mm. Joint size: 24/40. Allows for flexible tubing to be connected to apparatus for introduction of vacuum or pressure. Hose connection has a O.D. of 10mm at the largest serration and is bent downward at a 90[degree] angle to the inner joint.

ADAPTER, THERMOMETER, INLET. H: 50mm. Joint size: 14/20. Adapter has a #7 Chem-Thread at the top for vacuum tight seal of plain stem thermometers or any other tube having an O.D. between 4 and 7mm. Supplied complete with a Celcon compression cap and Viton o-ring.

ARSINE GENERATOR, IMPROVED. Arsine Generator, Complete. For arsine analysis using the diethyldithicarbamate (SDDC) colorimetric method. Design also meets specifications of ACS/USP, EPA and can be used with APHA Standard 104A.

ARSINE GENERATOR, IMPROVED. Scrubber/Absorber Tube only. For arsine analysis using the diethyldithicarbamate (SDDC) colorimetric method. Design also meets specifications of ACS/USP, EPA and can be used with APHA Standard 104A.

DISTILLING RECEIVER, MOISTURE TEST. 20ml. HxW: 400x130mm. Joint size: 24/40. Modified Dean-Stark receiver designed for solvents that are either lighter or heavier than water. Lower three-way fluoropolymer resin stopcock allows for withdraw or return of the distillate during the distillation process.

ROTARY EVAPORATOR ADAPTER, VIAL. EVAPORATOR BUMP TRAPS. 24/40 Glass Adapter Only. Adapter which permits the connection of standard laboratory dram vials directly to the vapor tube or a bump trap of a rotary evaportor. Adapter has a top outer joint of the listed size and a 20-400 G.P.I.

SUBLIMER, MICRO. Replacement Components. Lower Flask Only. Micro scale sublimer for use with quantities as small as 0.5 grams. The sublimer has a capacity of 3ml between the lower portion of the cold finger and the interior bottom of the flask.

SUBLIMER, MICRO. Replacement Components. Cold Finger Condenser Only. Micro scale sublimer for use with quantities as small as 0.5 grams. The sublimer has a capacity of 3ml between the lower portion of the cold finger and the interior bottom of the flask.

SUBLIMATOR, VACUUM, DAILEY . 40ml Sublimer Complete. Approx. HxW: 265x175mm. Capacity: 40ml. Joint Size: 40. O-Ring Size: 226. Clamp Size: 65. Valve Size: 0-4mm.

VACUUM MANIFOLD, FLUOROPOLYMER RESIN. Manifold with Right Hand Vacuum Connection. Number of Ports: 4; Stopcock Bore: 4mm. General purpose manifold with 4 of 6 ports. Main tube is 1in. OD with a serrated hose connection located at either the left or right side for vacuum connection.

VACUUM MANIFOLD, FLUOROPOLYMER RESIN. Manifold with Right Hand Vacuum Connection. Number of Ports: 6; Stopcock Bore: 4mm. General purpose manifold with 4 of 6 ports. Main tube is 1in. OD with a serrated hose connection located at either the left or right side for vacuum connection.

VACUUM MANIFOLD, FLUOROPOLYMER RESIN. Manifold with Left Hand Vacuum Connection. Number of Ports: 4; Stopcock Bore: 4mm. General purpose manifold with 4 of 6 ports. Main tube is 1in. OD with a serrated hose connection located at either the left or right side for vacuum connection.

VACUUM MANIFOLD, FLUOROPOLYMER RESIN. Manifold with Left Hand Vacuum Connection. Number of Ports: 6; Stopcock Bore: 4mm. General purpose manifold with 4 of 6 ports. Main tube is 1in. OD with a serrated hose connection located at either the left or right side for vacuum connection.

VACUUM MANIFOLD. With Right Hand Vacuum Connection. Number of Ports: 3; Valve Size: 0-4mm; Overall Width: 240mm. Single bank general purpose manifold with 3, 4, or 5 ports. Valves are either 0-4 or 0-8mm with CHEM-CAP plug allowing only glass and fluoropolymer resin contact with material being used.

VACUUM MANIFOLD. With Right Hand Vacuum Connection. Number of Ports: 3; Valve Size: 0-8mm; Overall Width: 350. Single bank general purpose manifold with 3, 4, or 5 ports. Valves are either 0-4 or 0-8mm with CHEM-CAP plug allowing only glass and fluoropolymer resin contact with material being used.

VACUUM MANIFOLD. With Right Hand Vacuum Connection. Number of Ports: 4; Valve Size: 0-4mm; Overall Width: 300mm. Single bank general purpose manifold with 3, 4, or 5 ports. Valves are either 0-4 or 0-8mm with CHEM-CAP plug allowing only glass and fluoropolymer resin contact with material being used.

VACUUM MANIFOLD. With Right Hand Vacuum Connection. Number of Ports: 4; Valve Size: 0-8mm; Overall Width: 425mm. Single bank general purpose manifold with 3, 4, or 5 ports. Valves are either 0-4 or 0-8mm with CHEM-CAP plug allowing only glass and fluoropolymer resin contact with material being used.

VACUUM MANIFOLD. With Right Hand Vacuum Connection. Number of Ports: 5; Valve Size: 0-4mm; Overall Width: 360mm. Single bank general purpose manifold with 3, 4, or 5 ports. Valves are either 0-4 or 0-8mm with CHEM-CAP plug allowing only glass and fluoropolymer resin contact with material being used.

VACUUM MANIFOLD. With Right Hand Vacuum Connection. Number of Ports: 5; Valve Size: 0-8mm; Overall Width: 500mm. Single bank general purpose manifold with 3, 4, or 5 ports. Valves are either 0-4 or 0-8mm with CHEM-CAP plug allowing only glass and fluoropolymer resin contact with material being used.

VACUUM MANIFOLD. With Left Hand Vacuum Connection. Number of Ports: 3; Valve Size: 0-4mm; Overall Width: 240mm. Single bank general purpose manifold with 3, 4, or 5 ports. Valves are either 0-4 or 0-8mm with CHEM-CAP plug allowing only glass and fluoropolymer resin contact with material being used.

VACUUM MANIFOLD. With Left Hand Vacuum Connection. Number of Ports: 3; Valve Size: 0-8mm; Overall Width: 350mm. Single bank general purpose manifold with 3, 4, or 5 ports. Valves are either 0-4 or 0-8mm with CHEM-CAP plug allowing only glass and fluoropolymer resin contact with material being used.

VACUUM MANIFOLD. With Left Hand Vacuum Connection. Number of Ports: 4; Valve Size: 0-4mm; Overall Width: 300mm. Single bank general purpose manifold with 3, 4, or 5 ports. Valves are either 0-4 or 0-8mm with CHEM-CAP plug allowing only glass and fluoropolymer resin contact with material being used.

VACUUM MANIFOLD. With Left Hand Vacuum Connection. Number of Ports: 4; Valve Size: 0-8mm; Overall Width: 425mm. Single bank general purpose manifold with 3, 4, or 5 ports. Valves are either 0-4 or 0-8mm with CHEM-CAP plug allowing only glass and fluoropolymer resin contact with material being used.

VACUUM MANIFOLD. With Left Hand Vacuum Connection. Number of Ports: 5; Valve Size: 0-4mm; Overall Width: 360mm. Single bank general purpose manifold with 3, 4, or 5 ports. Valves are either 0-4 or 0-8mm with CHEM-CAP plug allowing only glass and fluoropolymer resin contact with material being used.

VACUUM MANIFOLD. With Left Hand Vacuum Connection. Number of Ports: 5; Valve Size: 0-8mm; Overall Width: 500mm. Single bank general purpose manifold with 3, 4, or 5 ports. Valves are either 0-4 or 0-8mm with CHEM-CAP plug allowing only glass and fluoropolymer resin contact with material being used.

VACUUM / INERT MANIFOLD. Number of Ports: 3; Overall Width: 400mm. General purpose double bank manifold for use with vacuum and inert gas. Supplied with 0-4mm Chem-Cap plugs for greasefree operation. Both banks are made from 1/2in.

VACUUM / INERT MANIFOLD. Number of Ports: 4; Overall Width: 500mm. General purpose double bank manifold for use with vacuum and inert gas. Supplied with 0-4mm Chem-Cap plugs for greasefree operation. Both banks are made from 1/2in.

VACUUM / INERT MANIFOLD. Number of Ports: 5; Overall Width: 600mm. General purpose double bank manifold for use with vacuum and inert gas. Supplied with 0-4mm Chem-Cap plugs for greasefree operation. Both banks are made from 1/2in.

Double-Bank Vacuum /Inert Manifold. Double-bank manifold for use with vacuum and inert gas. Valves are 0-4 mm size while both banks are -+ O.D. Ports are 100 mm C to C and have 8 mm serrated hose connections. Valves are sealed at a 45- angle for easier manipulation. Has 3 ports.

Double-Bank Vacuum /Inert Manifold. Double-bank manifold for use with vacuum and inert gas. Valves are 0-4 mm size while both banks are -+ O.D. Ports are 100 mm C to C and have 8 mm serrated hose connections. Valves are sealed at a 45- angle for easier manipulation. Has 4 ports.

Double-Bank Vacuum /Inert Manifold. Double-bank manifold for use with vacuum and inert gas. Valves are 0-4 mm size while both banks are -+ O.D. Ports are 100 mm C to C and have 8 mm serrated hose connections. Valves are sealed at a 45- angle for easier manipulation. Has 5 ports.

General Purpose Vacuum/Inert Manifold. Banks are made from -+ medium wall tubing with 10 mm O.D. serrated connections. Stopcocks are glass 4 mm bore with lower vacuum chamber and are spaced 85 mm center to center. Has top right connection to inert gas, lower left connection for vacuum. Has 4 ports.

General Purpose Vacuum/Inert Manifold. Banks are made from -+ medium wall tubing with 10 mm O.D. serrated connections. Stopcocks are glass 4 mm bore with lower vacuum chamber and are spaced 85 mm center to center. Has top right connection to inert gas, lower left connection for vacuum. Has 5 ports.

Bubbler, High Capacity, with Check valve, Chemglass - CG-4522-02, Bubbler, with check valve, 28/15 joint

BUBBLER, PRESSURE RELEASE. vacuum. HxWxD: 130x100x100mm. Used for the purging of AIRFREE of vacuum apparatus with an inert gas. The pressure release valve is connected on one side to the low pressure gas source and the other side to a manifold or reaction vessel.

VACUUM CHECK VALVE. Valve has an 1/4in. O.D. precision ground ceramic ball which fits into the ground seat to effect a liquid seal. Tubing O.D. is 10mm while the overall length is approx. 125mm.

VALVE, CHECK. Similar to CG-4518, but having serrated hose connections on either end to accept flexible tubing. Tubing O.D. is 10mm while the overall length is approx. 100mm. Hose connection O.D. is 9mm at the middle ring.

GROUND JOINT, INNER, FULL LENGTH. Tubing O.D.xWall: 6.35x1.2mm. Joint size: 7/25.

GROUND JOINT, INNER, FULL LENGTH. Tubing O.D.xWall: 8.00x1.5mm. Joint size: 10/30.

GROUND JOINT, INNER, FULL LENGTH. Tubing O.D.xWall: 10.0x1.5mm. Joint size: 12/30.

GROUND JOINT, INNER, FULL LENGTH. Tubing O.D.xWall: 12.7x1.6mm. Joint size: 14/35.

GROUND JOINT, INNER, FULL LENGTH. Tubing O.D.xWall: 17.0x1.8mm. Joint size: 19/38.

GROUND JOINT, INNER, FULL LENGTH. Tubing O.D.xWall: 22x1.8mm. Joint size: 24/40.

GROUND JOINT, INNER, FULL LENGTH. Tubing O.D.xWall: 28x2.0mm. Joint size: 29/42.

GROUND JOINT, INNER, FULL LENGTH. Tubing O.D.xWall: 32x2.4mm. Joint size: 34/45.

GROUND JOINT, INNER, FULL LENGTH. Tubing O.D.xWall: 38x2.0mm. Joint size: 40/50.

GROUND JOINT, INNER, FULL LENGTH. Tubing O.D.xWall: 41x2.0mm. Joint size: 45/50.

GROUND JOINT, INNER, FULL LENGTH. Tubing O.D.xWall: 48x2.0mm. Joint size: 50/50.

GROUND JOINT, INNER, FULL LENGTH. Tubing O.D.xWall: 51x2.0mm. Joint size: 55/50.

GROUND JOINT, INNER, FULL LENGTH. Tubing O.D.xWall: 57x2.4mm. Joint size: 60/50.

GROUND JOINT, INNER, FULL LENGTH. Tubing O.D.xWall: 70x2.4mm. Joint size: 71/60.

GROUND JOINT, INNER, FULL LENGTH. Tubing O.D.xWall: 100x2.4mm. Joint size: 103/60.

GROUND JOINT, OUTER, FULL LENGTH. Tubing O.D.xWall: 10x1.5mm. Joint size: 7/25. Standard taper outer joint tooled on tubing approximately the same diameter as the top reinforcing ring, affording no hold-up below joint.

GROUND JOINT, OUTER, FULL LENGTH. Tubing O.D.xWall: 14x1.2mm. Joint size: 10/30. Standard taper outer joint tooled on tubing approximately the same diameter as the top reinforcing ring, affording no hold-up below joint.

GROUND JOINT, OUTER, FULL LENGTH. Tubing O.D.xWall: 16x1.2mm. Joint size: 12/30. Standard taper outer joint tooled on tubing approximately the same diameter as the top reinforcing ring, affording no hold-up below joint.

GROUND JOINT, OUTER, FULL LENGTH. Tubing O.D.xWall: 19x1.8mm. Joint size: 14/35. Standard taper outer joint tooled on tubing approximately the same diameter as the top reinforcing ring, affording no hold-up below joint.

GROUND JOINT, OUTER, FULL LENGTH. Tubing O.D.xWall: 22x1.8mm. Joint size: 19/38. Standard taper outer joint tooled on tubing approximately the same diameter as the top reinforcing ring, affording no hold-up below joint.

GROUND JOINT, OUTER, FULL LENGTH. Tubing O.D.xWall: 28x2.0mm. Joint size: 24/40. Standard taper outer joint tooled on tubing approximately the same diameter as the top reinforcing ring, affording no hold-up below joint.

GROUND JOINT, OUTER, FULL LENGTH. Tubing O.D.xWall: 32x2.4mm. Joint size: 29/42. Standard taper outer joint tooled on tubing approximately the same diameter as the top reinforcing ring, affording no hold-up below joint.

GROUND JOINT, OUTER, FULL LENGTH. Tubing O.D.xWall: 38x2.0mm. Joint size: 34/45. Standard taper outer joint tooled on tubing approximately the same diameter as the top reinforcing ring, affording no hold-up below joint.

GROUND JOINT, OUTER, FULL LENGTH. Tubing O.D.xWall: 45x2.0mm. Joint size: 40/50. Standard taper outer joint tooled on tubing approximately the same diameter as the top reinforcing ring, affording no hold-up below joint.

GROUND JOINT, OUTER, FULL LENGTH. Tubing O.D.xWall: 48x2.3mm. Joint size: 45/50. Standard taper outer joint tooled on tubing approximately the same diameter as the top reinforcing ring, affording no hold-up below joint.

GROUND JOINT, OUTER, FULL LENGTH. Tubing O.D.xWall: 54x2.4mm. Joint size: 50/50. Standard taper outer joint tooled on tubing approximately the same diameter as the top reinforcing ring, affording no hold-up below joint.

GROUND JOINT, OUTER, FULL LENGTH. Tubing O.D.xWall: 60x2.4mm. Joint size: 55/50. Standard taper outer joint tooled on tubing approximately the same diameter as the top reinforcing ring, affording no hold-up below joint.

GROUND JOINT, OUTER, FULL LENGTH. Tubing O.D.xWall: 64x2.4mm. Joint size: 60/50. Standard taper outer joint tooled on tubing approximately the same diameter as the top reinforcing ring, affording no hold-up below joint.

GROUND JOINT, OUTER, FULL LENGTH. Tubing O.D.xWall: 75x2.4mm. Joint size: 71/60. Standard taper outer joint tooled on tubing approximately the same diameter as the top reinforcing ring, affording no hold-up below joint.

GROUND JOINT, OUTER, FULL LENGTH. Tubing O.D.xWall: 110x3.0mm. Joint size: 103/60. Standard taper outer joint tooled on tubing approximately the same diameter as the top reinforcing ring, affording no hold-up below joint.

GROUND JOINT, OUTER, FULL LENGTH. Tubing O.D.XWall: 22x1.8mm. Joint size: 24/40. Standard taper outer joint tooled on the same size tubing as the CG-100 inner joints. All CG-102 outer joints are supplied standard with rings, but are available tooled without rings on a special order basis.

GROUND JOINT, OUTER, FULL LENGTH. Tubing O.D.XWall: 28x2.0mm. Joint size: 29/42. Standard taper outer joint tooled on the same size tubing as the CG-100 inner joints. All CG-102 outer joints are supplied standard with rings, but are available tooled without rings on a special order basis.

GROUND JOINT, OUTER, FULL LENGTH. Tubing O.D.XWall: 28x2.0mm. Joint size: 24/40. Standard taper outer joints tooled with reinforcing rings.

GROUND JOINT, OUTER, FULL LENGTH. Tubing O.D.XWall: 32x2.4mm. Joint size: 29/42. Standard taper outer joints tooled with reinforcing rings.

GROUND JOINT, OUTER, FULL LENGTH. Tubing O.D.XWall: 38x2.0mm. Joint size: 34/45. Standard taper outer joints tooled with reinforcing rings.

GROUND JOINT, OUTER, FULL LENGTH. Tubing O.D.XWall: 48x2.0mm. Joint size: 45/50. Standard taper outer joints tooled with reinforcing rings.

GROUND JOINT, INNER, MEDIUM LENGTH. Tubing O.D.XWall: 4.00x.80mm. Joint size: 5/12.

GROUND JOINT, INNER, MEDIUM LENGTH. Tubing O.D.XWall: 6.35x1.2mm. Joint size: 7/10.

GROUND JOINT, INNER, MEDIUM LENGTH. Tubing O.D.XWall: 6.35x1.2mm. Joint size: 7/15.

GROUND JOINT, INNER, MEDIUM LENGTH. Tubing O.D.XWall: 8.00x1.5mm. Joint size: 10/18.

GROUND JOINT, INNER, MEDIUM LENGTH. Tubing O.D.XWall: 10.0x1.5mm. Joint size: 12/18.

GROUND JOINT, INNER, MEDIUM LENGTH. Tubing O.D.XWall: 12.7x1.6mm. Joint size: 14/10.

GROUND JOINT, INNER, MEDIUM LENGTH. Tubing O.D.XWall: 12.7x1.6mm. Joint size: 14/20.

GROUND JOINT, INNER, MEDIUM LENGTH. Tubing O.D.XWall: 17.0x1.8mm. Joint size: 19/22.

GROUND JOINT, INNER, MEDIUM LENGTH. Tubing O.D.XWall: 22.0x1.8mm. Joint size: 24/25.

GROUND JOINT, INNER, MEDIUM LENGTH. Tubing O.D.XWall: 28x2.0mm. Joint size: 29/26.

GROUND JOINT, INNER, MEDIUM LENGTH. Tubing O.D.XWall: 32x2.4mm. Joint size: 34/28.

GROUND JOINT, INNER, MEDIUM LENGTH. Tubing O.D.XWall: 38x2.0mm. Joint size: 40/35.

GROUND JOINT, OUTER, MEDIUM LENGTH. Tubing O.D.XWall: 10x1.5mm. Joint size: 7/10.

GROUND JOINT, OUTER, MEDIUM LENGTH. Tubing O.D.XWall: 10x1.5mm. Joint size: 7/15.

GROUND JOINT, OUTER, MEDIUM LENGTH. Tubing O.D.XWall: 14x1.2mm. Joint size: 10/18.

GROUND JOINT, OUTER, MEDIUM LENGTH. Tubing O.D.XWall: 16x1.2mm. Joint size: 12/18.

GROUND JOINT, OUTER, MEDIUM LENGTH. Tubing O.D.XWall: 19x1.8mm. Joint size: 14/20.

GROUND JOINT, OUTER, MEDIUM LENGTH. Tubing O.D.XWall: 22x1.8mm. Joint size: 19/22.

GROUND JOINT, OUTER, MEDIUM LENGTH. Tubing O.D.XWall: 28x2.0mm. Joint size: 24/25.

GROUND JOINT, OUTER, MEDIUM LENGTH. Tubing O.D.XWall: 32x2.4mm. Joint size: 29/26.

GROUND JOINT, OUTER, MEDIUM LENGTH. Tubing O.D.XWall: 38x2.0mm. Joint size: 34/28.

GROUND JOINT, OUTER, MEDIUM LENGTH. Tubing O.D.XWall: 45x2.0mm. Joint size: 40/35.

GROUND JOINT, OUTER, MEDIUM LENGTH. Tubing O.D.XWall: 12.7x1.6mm. Joint size: 14/20. Standard taper outer joint tooled on the same diameter tubing as the CG-104 inner joints.

GROUND JOINT, OUTER, MEDIUM LENGTH. Tubing O.D.XWall: 17x1.8mm. Joint size: 19/22. Standard taper outer joint tooled on the same diameter tubing as the CG-104 inner joints.

GROUND JOINT, INNER, WITH HOOKS. Tubing O.D.xWall: 12.7x1.6mm. Joint size: 14/20. Inner joint with two hooks 180[degree] apart just above the grind.

Category