• 0
Shop Products $

Frame Reactor Support 400Mm Flange 50L. Reactor Support Frame, Mobile, Jacketed, 50L, 400mm Flange, Oversized Rugged S.S. Uprights and Heavy Duty PTFE Coated Aluminum Fittings Provide Maximum Strength and Chemical Durability, All S.S. Uprights are Passiva

Frame Shielded Support 400Mm Flange 100L. Shielded Reactor Support Frame, Mobile, Jacketed, 100L, 400mm Flange, Oversized Rugged S.S. Uprights and Heavy Duty PTFE Coated Aluminum Fittings Provide Maximum Strength and Chemical Durability, All S.S. Uprights

Cart Heavy Duty With 8Ft Tie Down Strap. Cart, Heavy Duty, Circulator, Supplied with 8ft Tie Down Strap, for use with Huber Unistat models 405 and 705 circulators, raises the circulators so that the controllers are easily viewed and may make it possible t

Adapter, 45/50, PTFE with 3/8in Compression Fitting Loosening Ring.

Reaction Block Tri-Block Bk Hard Coated. Tri-Block Reaction Block, is designed to fit directly on 135mm diameter circular top hot plate stirrers. Versatile design of the tri-block fits the most common vial sizes on one hot plate: 11ea- 1 Dram vials, 11ea

Probe/Sensor Only Pt100 3Mmdiameter Velp.

Digital Thermoregulator W/Built In Timer. Digital Thermoregulator, with Built In Timer, is equipped with innovative Fuzzy Logic technology that provides accurate set point +/- 0.5 C, Digital count down timer shuts off heating- adjustable from 0-24:59 (h:m

Vertical Support Rod Velp.

Rod Support/Holding Pt Sensor Hot Plate. Rod, Support/Holding, PT Sensor, Hot Plate, VELP, For fastening a temperature sensor / probe with a boss head to the vertical support rod on a hotplate

Adapter Offset Ss For Velp Hotplate. Offset Adapter, for Velp Hotplates, Stainless Steel, Supplied with M8 Bolt, can be used with cooling/heating blocks up approx. 8-5/8in/220mm diameter, Offset created by adapter is 20mm center to center. Supplied comple

Protective Silicone Cover for CG-1995-V and CG-1994-V Hotplates.

Protective Silicone Cover for AREX 6 (CG-1996-V10, CG-1997-V-10 & CG-1997-W-10) Hotplates.

Hotplate/Tri-Block Combo 1 For Stirrer. Hotplate and Tri-block, COMBO 1, for Magnetic Hot Plate Stirrers, Digital Displays, With Timers, 135Mm Diameter Round Top

Hotplate Tri-Block And Hardware Combo 2. Hotplate, Tri-block and hardware, COMBO 2, for Magnetic Hot Plate Stirrers, Digital Displays, With Timers, 135Mm Diameter Round Top

Kit Complete Digital Hotplate Arex6 115V. COMPLETE Digital Hotplate Kit, AREX-6 with probe, with Vertical Support Rod, Boss Head, and Support/Holding Rod, 115V, for Magnetic Hotplate Stirrer

Holder Clamp Heavy Duty Fits 3/4In Rod. Heavy Duty Clamp Holder, Fits 3/4in Support Rod, epoxy coated alloy clamp has high tensile strength and corrosion resistance, Can be used to support stirrers, temperature monitors and condensers, Large hand knobs al

Coupling Adapter, S.S, for Tru-Stir stirrer shaft coupling.

Shaft Coupling Compact Tru-Stir 6.35Mm. Tru-Stir Compact Shaft Coupling fits 6.35mm Shaft OD for use with Jacobs Chuck, eliminates the need to use rubber hose or universal adapters to attach your stirrer shafts to overhead stir motors, incorporates a uni

Shaft Coupling Stirrer 30Mm 3/8Inod Stud. Stirrer Shaft Coupling, 30mm, 3/8in OD Stud, design allows for easier assembly and disassembly between the motor, 30mm glass stirrer shaft, with universal joint compensates for misalignment of drive motor/glass st

Coupling Assembly Complete Cg-2033-B-25. Coupling Assembly, Complete, Split Coupling, 30mm, Universal, Stainless Bushing and Upper Adapter For Use with CG-2033-B-25, Stainless steel collar/bushing and upper coupling attach directly to the motor shaft, For

Coupling Assembly Complete F/ Cg-2025-20. Coupling Assembly Complete, Split Coupling, 30mm, Universal, Stainless Bushing and Upper Adapter For Use with CG-2025-20, Stainless steel collar/bushing and upper coupling attach directly to the motor shaft, For u

Coupling Assembly Complete Cg-2033-X-11. Coupling Assembly Complete, Split Coupling, 30mm, Universal, Stainless Bushing and Upper Adapter For Use with with CG-2033-X-11, Stainless steel collar/bushing and upper coupling attach directly to the motor shaft,

Rotary Bearing Taper Lock, 10mm, Ferrule, Nylon, for mechanical seal bearing.

Rotary Bearing Taper Lock, 19mm, Ferrule, Nylon, for mechanical seal bearing.

Rotary Bearing Taper Lock, 25.4mm, Ferrule, Nylon, for mechanical seal bearing.

Rotary Bearing Taper Lock, 31 mm, Ferrule, Nylon, for mechanical seal bearing.

Shaft Stirring 10 Mm 400 Mm Oal Od 42 Mm. Stirring Shaft, 10mm, Clockwise, Polished, Glass Agitator, Three Blade, 400mm OAL, Agitator OD 42mm, for use with 100-250mL Reactors, is precision ground and polished to fit our CG-2077-H, CG-2077-G and CG-2077-U

Shaft Stirring 10 Mm 400 Mm Oal Od 50 Mm. Stirring Shaft, 10mm, Clockwise, Polished, Glass Agitator, Three Blade, 400mm OAL, Agitator OD 50mm, for use with 100-250mL Reactors, is precision ground and polished to fit our CG-2077-H, CG-2077-G and CG-2077-U

Shaft Stirring 10 Mm 460 Mm Oal Od 50 Mm. Stirring Shaft, 10mm, Clockwise, Polished, Glass Agitator, Three Blade, 460mm OAL, Agitator OD 50mm, for use with 500mL Reactors, is precision ground and polished to fit our CG-2077-H, CG-2077-G and CG-2077-U styl

Shaft Stirring 10 Mm 460 Mm Oal Od 66 Mm. Stirring Shaft, 10mm, Clockwise, Polished, Glass Agitator, Three Blade, 460mm OAL, Agitator OD 66mm, for use with 500mL Reactors, is precision ground and polished to fit our CG-2077-H, CG-2077-G and CG-2077-U styl

Shaft Stirring 10 Mm 525 Mm Oal Od 50 Mm. Stirring Shaft, 10mm, Clockwise, Polished, Glass Agitator, Three Blade, 525mm OAL, Agitator OD 50mm, for use with 1,000mL Reactors, is precision ground and polished to fit our CG-2077-H, CG-2077-G and CG-2077-U st

Shaft Stirring 10 Mm 525 Mm Oal Od 66 Mm. Stirring Shaft, 10mm, Clockwise, Polished, Glass Agitator, Three Blade, 525mm OAL, Agitator OD 66mm, for use with 1,000mL Reactors, is precision ground and polished to fit our CG-2077-H, CG-2077-G and CG-2077-U st

Agitator One-Piece Ptfe Lower Four Blade. One-Piece PTFE Lower Agitator, 13in, Four Blade, For Use with 30mm Shafts, For use with 400mm ID Flange Reactor, The smooth machined surface has no seams, joints or crevices for material to collect, provides excel

Stirrer Shaft Replacement 25.4 Mm 30 L. Stirrer Shaft, Replacement, 25.4mm, Reactor Size: 30L, Fits Support Frame: CG-1968-X-12, Overall Length: 40.9in, for use with Chemglass process reactors, Designed to utilize CG-2095 and CG-2096 PTFE agitators, Lower

Heating Blanket 115V-3L 130 Watt 1 Latch. Heating Blanket 115V-3L 130 Watt, Used with a temperature controller and rtd temperature sensor for heating media inside a vessel to temperature, 5Watts Per Sq In Male iec connector, 6ft Cord (18-2) with CJ14 Plug, Dimensions: 15in X 2.5in Tall with 1 Latch

Heating Blanket 115V-Low Pro 190 Watt. Heating Blanket 115V-Low Profile 3/6L 190 Watt, Male Iec Connector for Use with Temperature Controllers, Heating At 5 Watts/Sq.In, Flask Size: Low Profile 3l & 6l Vessel, Dimension (IN.): 2 X 26.5, 2 Latches, 6ft Cord (18-2) with Cj14 Plug

Heat Blanket 115V-500Ml Flask 50 Watt. Heating Blanket 115V-500mL 50 Watt, used with a temperature controller and RTD temperature sensor for heating media inside a vessel to temperature, Male Iec Connector, 6f Cord (18-2) with C-14 Plug, Flask Size: 500ml, Dimension (IN.): 1 X 10.5, 1 Latch

Heating Blanket 115V-1L 75 Watt 1 Latch. Heating Blanket 115V-1L 75 Watt, Used with a temperature controller and rtd temperature sensor for heating media inside a vessel to temperature, Male iec connector, 1 latch, 6ft Cord (18-2) with CJ14 Plug, Heating at 5 watts/sq.in, Dimension: 1 X 14in

Heating Blanket 115V-3L 150 Watt 1 Latch. Heating Blanket 115V-3L 150 Watt, Used with a temperature controller and rtd temperature sensor for heating media inside a vessel to temperature, Male iec connector, 1 latch, 6ft Cord (18-2) with CJ14 Plug, Heating at 5 watts/sq.in, Dimension: 2 X 17.5in

Heating Blanket 115V-6L 300 Watt 1 Latch. Heating Blanket 115V-6L 300 Watt, Used with a temperature controller and rtd temperature sensor for heating media inside a vessel to temperature, Male iec connector, 1 latch, 6ft Cord (18-2) with CJ14 Plug, Heating at 5 watts/sq.in, Dimension: 3 X 22-1/4in

Heating Blanket 115V-8L 375 Watt 1 Latch. Heating Blanket 115V-8L 375 Watt, Used with a temperature controller and rtd temperature sensor for heating media inside a vessel to temperature, Male iec connector, 1 latch, 6ft Cord (18-2) with CJ14 Plug, Heating at 5 watts/sq.in, Dimension: 3 X 26.5in

Heating Blanket 115V-15L 750Watt 1 Latch. Heating Blanket 115V-15L 750 Watt, Used with a temperature controller and rtd temperature sensor for heating media inside a vessel to temperature, Male iec connector, 1 latch 6ft Cord (18-2) With CJ14 Plug, Heating at 5 watts/sq.in, Dimension: 5 X 33-1/4in

Heat Blanket 115V-36L Flask 1200 Watt. Heating Blanket 115V-36L 1200 Watt, used with a temperature controller and RTD temperature sensor for heating media inside a vessel to temperature, Male Iec Connector, 6f Cord (18-2) with Cj14 Plug, Flask Size: 36l, Dimension: 5 X 48 3/4in, 3 Latches

Heat Blanket 230V-500Ml Flask 50 Watt. Heating Blanket 230V-500mL 50 Watt, used with a temperature controller and RTD temperature sensor for heating media inside a vessel to temperature, Male Iec Connector, 6f Cord (18-2) with C-14 Plug, Flask Size: 500ml, Dimension (IN.): 1 X 10.5, 1 Latch

Heating Blanket 230V-1L 75 Watt 1 Latch. Heating Blanket 230V-1L 75 Watt, Used with a temperature controller and rtd temperature sensor for heating media inside a vessel to temperature Male iec connector, 1 latch, 6ft Cord (18-2) with CJ14 Plug, Heating at 5 watts/sq.in, Dimension: 1 X 13 3/4in

Heating Blanket 230V-3L 150 Watt 1 Latch. Heating Blanket 230V-3L 150 Watt, Used with a temperature controller and rtd temperature sensor for heating media inside a vessel to temperature, Male iec connector, 1 latch 6ft Cord (18-2) with CJ14 Plug, Heating at 5 watts/sq.in, Dimension: 2 X 17.5in

Heating Blanket 230V-6L 300 Watt 2Latch. Heating Blanket 230V-6L 300 Watt, Used with a temperature controller and rtd temperature sensor for heating media inside a vessel to temperature, Male iec connector, 2 latch, 6ft Cord (18-2) with CJ14 Plug, Heating at 5 watts/sq.in, Dimension: 3 X 22 1/4in

Heating Blanket 230V-8L 375 Watt 2Latch. Heating Blanket 230V-8L 375 Watt, Used with a temperature controller and rtd temperature sensor for heating media inside a vessel to temperature, Male iec connector, 2 latch, 6ft Cord (18-2) with CJ14 Plug, Heating at 5 watts/sq.in, Dimension: 3 X 26.5in

Heat Blanket 230V-36L Flask 1200 Watt. Heating Blanket 230V-36L 1200 Watt, used with a temperature controller and RTD temperature sensor for heating media inside a vessel to temperature, Male Iec Connector, 6f Cord (18-2) with Cj14 Plug, Flask Size: 36l, Dimension: 5 X 47 3/4in, 3 Latches

Silicone Heating Pad 7Sq-115V Controller. Silicone Heating Pad 7sq - 115v for Bellco Temperature Controllers, Dimensions 7 Sq, Material Red Silicone Foam Back, Thickness 38, Spinner Vessels Up To 3l, 150 Watts, With Iec 60320 C14 Male Plug, High Limit Cutoff Up To 225f, for Temperature Controller

Heating Blanket 115V-15L 325Watt 3 Latch. Heating Blanket 115V-15L 325 Watt, Used with a temperature controller and rtd temperature sensor for heating media inside a vessel to temperature, Male iec connector, 3 latches, 6ft Cord (18-2) With CJ14 Plug, Heating at 5 watts/sq.in, Dimension: 5 X 33in

Heating Blanket 115V-36L 375Watt 3 Latch. Heating Blanket 115V-36L 375 Watt, Used with a temperature controller and rtd temperature sensor for heating media inside a vessel to temperature, Male iec connector, 3 latches, 6ft Cord (18-2) With CJ14 Plug, Heating at 5 watts/sq.in, Dimension: 5 X 48in

Heating Blanket 115V-36L 600Watt 3 Latch. Heating Blanket 115V-36L 600 Watt, Used with a temperature controller and rtd temperature sensor for heating media inside a vessel to temperature, Male iec connector, 3 latches, 6ft Cord (18-2) With CJ14 Plug, Heating at 5 watts/sq.in, Dimension: 5 X 48in

Heating Blanket 230V-15L 325Watt 3 Latch. Heating Blanket 230V-15L 325 Watt, Used with a temperature controller & rtd temperature sensor for heating media inside a vessel to temperature, Male iec connector, 3 latches, 6ft Cord (18-2) With CJ14 Plug, Heating at 5 watts/sq.in, Dimension: 5 X 33-1/4in

Heating Blanket 230V-36L 375Watt 3 Latch. Heating Blanket 230V-36L 375 Watt, Used with a temperature controller & rtd temperature sensor for heating media inside a vessel to temperature, Male iec connector, 3 latches, 6ft Cord (18-2) With CJ14 Plug, Heating at 5 watts/sq.in, Dimension: 5 X 47-3/4in

Heating Blanket 230V-36L 600Watt 3 Latch. Heating Blanket 230V-36L 600 Watt, Used with a temperature controller & rtd temperature sensor for heating media inside a vessel to temperature, Male iec connector, 3 latches, 6ft Cord (18-2) With CJ14 Plug, Heating at 5 watts/sq.in, Dimension: 5 X 447 3/4in

Heat Blanket 115V-3L Low Watt Special. Heating Blanket 115V-3L 50 Watt, Low Watt, used with a temperature controller and RTD temperature sensor for heating media inside a vessel to temperature, Male Iec Connector, 6f Cord (18-2) with CJ14 Plug, Flask Size: 500ml, Dimension: 2 X 29.5in, 1 Latch

Fitting Compression W/10 Holes SS 1/4In. Large Flange Headplate Assembly with 10 Holes, designed using our standard 45mm blue polypropylene open top caps and white silicone gaskets. 200mm Large Flange Headplate 10-Port, 1 Center for Drive Motor, Dimensions14 x 10 x 4 in, 1/4in

Fitting Compression W/10 Holes SS 1/2In. Large Flange Headplate Assembly with 10 Holes, designed using our standard 45mm blue polypropylene open top caps and white silicone gaskets. 200mm Large Flange Headplate 10-Port, 1 Center for Drive Motor, Dimensions14 x 10 x 4 in, 1/2in

Fitting Compression W/10 Holes SS 5/16In. Large Flange Headplate Assembly with 10 Holes, designed using our standard 45mm blue polypropylene open top caps and white silicone gaskets. 200mm Large Flange Headplate 10-Port, 1 Center for Drive Motor, Dimensions14 x 10 x 4 in, 5/16in

Fitting Compression Reducer 1/2 To 1/4In. Compression Reducer Fitting, These fittings are designed specifically for the bellco control systems and fit through a 5/16in fitting on the stainless steel headplate. Stainless steel Size: 1/2in - 1/4in

Probe Adapter Old-Hp 1.5In Ext Npt Thr. Probe Adapter-old HP 1.5 Ext NPT Thread, 316 l stainless steel probe adapter extension, threaded. Dimensions: 5 x 8 in

Probe Adapter 1.7, 316 l stainless steel probe adapter extension, threaded, Dimensions: 5 x 8 in.

Probe Holder 316L SS Autclv 45Mm 1.7In. Probe Holder 45mm, stainless steel probe holder is designed to be used with our 45mm blue polypropylene open top caps and white silicone gaskets. 316 L Stainless Steel, Polypropylene Caps, Autoclavable, 13.5 Thread for pH And Do Probes, Dimensions: 5 x 8 in

Tube Sst Bent Harvesting 5L 1/2 X 16In. Stainless Steel Bent Harvesting Tube, 316l stainless steel bent harvesting tube for 5l flat bottom omni vessel. Use with large flange head-plate. Size: 1/2in x 16in Id:.430in

Tube Sst Bent Harvesting 8L 1/2 X 18In. Stainless Steel Bent Harvesting Tube, Material: 316l SST with electropolish finish - outside only Dimensions: 1/2in od x.430inid x 18in l

Tube Sst Bent Harvesting SS 15L 1/2X20In. Stainless Steel Bent Harvesting Tube, 316l stainless steel bent harvesting tube for 15l flat bottom omni vessel. Use with large flange head-plate. Size: 1/2in x 20in Id:.430in

Tube Sst Bent Harvesting 36L 1/2X 22In. Stainless Steel Bent Harvesting Tube, 316l stainless steel bent harvesting tube for 36l flat bottom omni vessel. Use with large flange head-plate. Size: 1/2in x 22in Id:.430in

Tube Sst Curved Harvest SS 5L 1/2X 14In. Stainless steel curved harvesting tube for 5l round bottom omni vessels. Manufactured from 316l stainless steel with ra finish of 32 micro inch or better inside and out electropolish finish. Size: 5l Dimensions: 1/2 x.430 x 14 1/4in

Tube Sst Curved Harvest SS 8L 1/2X20In. Stainless steel curved harvesting tube for 8l round bottom omni vessels. Manufactured from 316l stainless steel with ra finish of 32 micro inch or better inside and out electropolish finish. Size: 8l Dimensions: 1/2in x.430 x 20in

Harvesting Port Assembly SS 3/8In 10L. English threads Fits into 3/8in holes in headplate material 316l SST with electropolish finish - ra 32 finish inside & out Inside dimensions:.250in od x 19 1/4in overall length insertion length: 18in with hose barbs supply with SST nut & o-ring

Tube Sst Curved Harvesting 15L 1/2X22In. Stainless steel curved harvesting tube for 15l round bottom omni vessels. Manufactured from 316l stainless steel with ra finish of 32 micro inch or better inside and out electropolish finish. Size: 15l Dimensions: 1/2in x.430 x 22in

Tube Sst Curved Harvesting 36L 1/2X24In. Stainless steel curved harvesting tube for 36l round bottom omni vessels. Manufactured from 316l stainless steel with ra finish of 32 micro inch or better inside and out electropolish finish. Size: 36l Dimensions: 1/2in x.430 x 24in

Fitting Compression 45Mm Cap PP 2.5In. Bellco compression fittings, Designed using our standard 45mm blue polypropylene open top caps and white silicone gaskets. Insertion of these probes into sidearms or vessels, Dimension: 5 x 8 in

Barb Assembly Bioreactor Hose 4-45 45Mm. 4-45 Bioreactor Hose Barb Assembly, 45mm, 316l Stainless Steel Compression Fitting And Hose Barb, Blue Polypropylene 45mm Screw Cap with Open Top, White Silicone Rubber Gasket, Dimensions: 9 x 5 x 1 in

Capseal Probe SS W/ PTFE Iob 4 Ports 1L. Stainless Steel Probe Capseal, with PTFE IOB 4 Ports, 100mm iob probe cap seal, Material: 316l stainless steel, red-silicone sealing gasket with a 100mm blue polypropylene screw cap. Probe cap seal has four accessory ports, Size: 1L

Capseal Probe SS W/ PTFE Iob 4Ports 3L. Probe Capseal 3L with PTFE IOB 4Ports, Stainless steel 100mm iob probe cap seal, Material: 316l stainless steel, Red-silicone sealing gasket with a 100mm blue polypropylene screw cap. Probe cap seal has four accessory ports, Dimensions: 17x7x6 in, Size: 3L

Insect System Dig Micro-Carrier 115V 3L. Digital Micro-Carrier Insect System, Designed for growing insect cell cultures such as sf9 and sf21 cells. The system comes complete with all accessories needed to grow your insect culture line for expression. 115v, Dimension: 18 x 17 x 14 in

Insect System Dig Micro-Carrier 230V 3L. Digital Micro-Carrier Insect System, Designed for growing insect cell cultures such as sf9 and sf21 cells. The system comes complete with all accessories needed to grow your insect culture line for expression. 230v, Dimensions: 18 x 17 x 14 in

Insect System Digital Iob 115V 3L 1/4In. Digital IOB Insect System 115v, Designed for growing insect cell cultures such as sf9 and sf21 cells. The system comes complete with all accessories needed to grow your insect culture line for expression. Dimensions: 18 x 17 x 14 in, Size: 3l

Insect System Digital Iob 230V 3L 1/4In. Digital IOB Insect System 230v, Designed for growing insect cell cultures such as sf9 and sf21 cells. The system comes complete with all accessories needed to grow your insect culture line for expression. Dimensions: 18 x 17 x 14 in, Size: 3l

Bell-Flo Iob Assembly 70Mm 100Ml 8X4X7In. Bell-Flo IOB Assembly, Bell-Flo iob assembly was designed to be used with the bell-flo vessel with bottom indents and 3 vertical baffles for optimal mixing. Cap Size: 70mm, Dimensions: 8 x 4 x 7 in, Vessel: 100mL

Insect Sys Process Micro-Carrier 115V 3L. Process Micro-Carrier Insect System, Designed for growing insect cell cultures such as sf9 and sf21 cells. The system comes complete with all accessories needed to grow your insect culture line for expression. 115v, Dimensions: 18 x 17 x 14 in

Insect Sys Process Micro-Carrier 230V 3L. Process Micro-Carrier Insect System, Designed for growing insect cell cultures such as sf9 and sf21 cells. The system comes complete with all accessories needed to grow your insect culture line for expression. 230v, Dimensions: 18 x 17 x 14 in

Bell-Flo Iob Assembly Boro 32Mm 250Ml. Bell-Flo iob assembly, Designed to be used with the bell-flo vessel with bottom indents and 3 vertical baffles for optimal mixing. Cap Size: 70mm, Sidearm Cap: 32mm, Dimensions: 130in X 65in, Vessel: 250ml

Bell-Flo Flask only Boro 70Mm 500Ml. Bell-Flo Flask only, Manufactured from type 1 class a Borosilicate glass. Bottom indent and 3 vertical baffles for optimal mixing. Sidearm cap: 45mm Center cap: 100mm Dimensions: 170in x 110in Flask size: 500ml

Bell-Flo Iob Assembly Boro 100Mm 500Ml. Bell-Flo iob assembly, Designed to be used with the bell-flo vessel with bottom indents and 3 vertical baffles for optimal mixing. With Rugged stainless steel PTFE internal bearing impeller assemblies, Cap Size: 100mm, Sidearm Cap: 45mm, Vessel: 500ml

Bell-Flo Iob Assembly Boro 70Mm 500Ml. Bell-Flo iob assembly, Designed to be used with the bell-flo vessel with bottom indents and 3 vertical baffles for optimal mixing. With Rugged stainless steel PTFE internal bearing impeller assemblies, Cap Size: 70mm, Sidearm Cap: 32mm, Vessel: 500ml

Bell-Flo Iob Assembly Boro 1L 220X95In. Bell-Flo iob assembly Used with the bell-flo vessel with bottom indents and 3 vertical baffles for optimal mixing. Rugged stainless steel PTFE internal bearing impeller assemblies, Cap Size: 100mm, Sidearm Cap: 45mm, Dimensions: 220in X 95in, Size: 1L

Bell-Flo Iob Assembly Boro 100Mm PTFE 3L. Bell-Flo IOB Assembly, Unique PTFE paddle design promotes culture aeration Rugged stainless steel/PTFE internal bearing assemblies 100 mm cap, Size: 3L

Process Iob Insect System 115V 3L 1/4In. Process IOB Insect System, Designed for growing insect cell cultures such as sf9 and sf21 cells. The system comes complete with all accessories needed to grow your insect culture line for expression. 115v, Dimensions18 x 17 x 14 in

Process Iob Insect System 230V 3L 1/4In. Process IOB Insect System, Designed for growing insect cell cultures such as sf9 and sf21 cells. The system comes complete with all accessories needed to grow your insect culture line for expression. 230v, Dimensions18 x 17 x 14 in

Screw Cap Assembly Mc PP 70Mm 100-500Ml. Micro-Carrier Screw Cap Assembly, Material: Polypropylene, screw cap with silicone gasket pouring ring and compression fitting. Material: Polypropylene, Cap Size: 70mm, for Flask 100-500mL

Screw Cap Assembly Mc PP 100Mm 500Ml-3L. Micro-Carrier Screw Cap Assembly, Material: Polypropylene, Screw cap with silicone gasket pouring ring and compression fitting. Cap Size: 100mm, for Flask 500mL - 3L

Holder Probe Blue Open Top PP Cap 32 Mm. Probe Holder, Includes GL32 blue open top polypropylene cap and white silicone gasket, designed specifically for the Bio-Probe Low Volume Spinner Flask, Also designed to secure pH and DO Probe into 32mm sidearms

Screw Cap Assembly Microcarrier PP 100Mm. Micro-Carrier Screw Cap Assembly, Material: Polyproplene, Cap Size: 100mm, for Flask 6-36L

Screw Cap Assembly Black Phenolic 51Mm. Screw Cap Assembly, Black Phenolic, resist the effects of temperature and steam autoclaving, non-toxic white rubber liner, Consists of Screw Cap Liner And Stopper Or Compression Fitting, Size: 51 mm, Dimensions: 9 x 5 x 1.5 in

Shaft Assembly Stainless Steel 100 Ml. Shaft Assembly, Material: 316L stainless steel, Impeller assembly for micro-carrier spinner flasks, 1965 Series Micro-Carrier Spinner Flask, Weight: 32 oz, Size: 100ml, Dimensions: 5 x 1 x 1.5 in

Shaft Assembly Stainless Steel 250 Ml. Shaft Assembly, Material: 316L stainless steel, Impeller assembly for micro-carrier spinner flasks, 1965 Series Micro-Carrier Spinner Flask, Weight: 32 oz, Size: 250ml, Dimensions: 6 x 1 x 1.5 in

Shaft Assembly Stainless Steel 500 Ml. Shaft Assembly, Material: 316L stainless steel, Impeller assembly for micro-carrier spinner flasks, 1965 Series Micro-Carrier Spinner Flask, Weight: 48 oz, Size: 500mL, Dimensions: 8 x 1 in

Category